Lazerinis retrorefleksinis jutiklis OBR12M-R100-2EP-IO-V31-L

Prekės kodas: PF.267075-0121

Būklė: Nauja prekė

Gamintojas:

Lazerinis retroreflekcinis jutiklis su poliarizacijos filtru.

Stačiakampis, 2 push-pull (4-in-1) outputs, Sn=0…12m, IO-Link, jungtis M8x1, 4-pin, PC korpusas, IP67 / IP69 / IP69K. 

Pepperl+Fuchs OBR12M-R100-2EP-IO-V31-L

Kodas: PF.267075-0121

Šiuo metu prekės neturime

0,00 € be PVM

Charakteristikos

Jutiklio forma Stačiakampis
Korpuso (montavimo) dydis 11 x 44,5 x 21,5mm Stačiakampis
Medžiaga Polikarbonatas, PC
Veikimo atstumas 0...12000 mm
Produkto tipas Retrorefleksinis
Jungtis M8x1
Kontaktų skaičius 4
Veikimo funkcija 2 NO/NC reguliuojamas
Išėjimo tipas PNP/NPN
Maitinimo įtampa 10-30 VDC
Darbinė temperatūra -40°C ... +60°C
Apsaugos klasė IP69K
Jutiklio tipas Optiniai jutikliai

Apie prekę

General specifications
Effective detection range 0 ... 12 m
Reflector distance 0.2 ... 12 m
Threshold detection range 15 m
Reference target H50 reflector
Light source laser diode DuraBeam
Light type modulated visible red light
Polarization filter yes
Laser nominal ratings
Note LASER LIGHT , DO NOT STARE INTO BEAM
Laser class 1
Wave length 680 nm
Beam divergence > 5 mrad d63 < 2 mm in the range of 250 mm ... 750 mm
Pulse length 1.6 µs
Repetition rate max. 17.6 kHz
max. pulse energy 9.6 nJ
Diameter of the light spot approx. 30 mm at a distance of 12 m
Opening angle approx. 0.3 °
Ambient light limit EN 60947-5-2
Functional safety related parameters
MTTFd 672 a
Mission Time (TM) 20 a
Diagnostic Coverage (DC) 0 %
Indicators/operating means
Operation indicator LED green:
constantly on - power on
flashing (4Hz) - short circuit
flashing with short break (1 Hz) - IO-Link mode
Function indicator Yellow LED:
Permanently lit - light path clear
Permanently off - object detected
Flashing (4 Hz) - insufficient operating reserve
Control elements Light-on/dark-on changeover switch
Control elements sensitivity adjustment
Parameterization indicator IO link communication: green LED goes out briefly (1 Hz)
Electrical specifications
Operating voltage 10 ... 30 V DC
Ripple max. 10 %
No-load supply current < 20 mA at 24 V supply voltage
Protection class III
Interface
Interface type IO-Link ( via C/Q = pin 4 )
IO-Link revision 1.1
Device ID 0x110202 (1114626)
Transfer rate COM2 (38.4 kBit/s)
Min. cycle time 2.3 ms
Process data width Process data input 2 Bit
Process data output 2 Bit
SIO mode support yes
Compatible master port type A
Output
Switching type The switching type of the sensor is adjustable. The default setting is:
C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link
/Q - Pin2: NPN normally closed / light-on, PNP normally open / dark-on
Signal output 2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected
Switching voltage max. 30 V DC
Switching current max. 100 mA , resistive load
Usage category DC-12 and DC-13
Voltage drop ≤ 1.5 V DC
Switching frequency 2000 Hz
Response time 250 µs
Conformity
Communication interface IEC 61131-9
Product standard EN 60947-5-2
Laser safety EN 60825-1:2014
Approvals and certificates
EAC conformity TR CU 020/2011
UL approval E87056 , cULus Listed , class 2 power supply , type rating 1
FDA approval IEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
Ambient conditions
Ambient temperature -40 ... 60 °C (-40 ... 140 °F)
Storage temperature -40 ... 70 °C (-40 ... 158 °F)
Mechanical specifications
Housing width 11 mm
Housing height 44.5 mm
Housing depth 21.5 mm
Degree of protection IP67 / IP69 / IP69K
Connection M8 x 1 connector, 4-pin
Material
Housing PC (Polycarbonate)
Optical face PMMA
Mass approx. 10 g

Nejautrus difuzinio ar net veidrodinio atspindžio signalui, dar vadinama M.S.R. funkcija (MSR = Mirror Surface Rejection).
Tais atvejais, kai objektas atspindėdamas šviesą dalinai pasuka poliarizacijos plokštumą (pvz. kartoninės dėžutės, apvyniotos strech plėvele), tinkamas sprendimas būtų naudoti prašvietimo principą (Trough-Beam).

Jautrumo derinimui naudoti atsuktuvą su PH1 antgaliu. Rekomenduojamas- WERA Kraftform Micro 2050 serijos WR.118023.

Rekomenduojamos susijusios prekės

Atsisiųsti

GAUKITE NAUJIENAS!

Prisijunkite nemokamai dabar ir pirmieji gaukite naujienas, informaciją apie nuolaidas ir specialius pasiūlymus.